燕山大学教师个人主页系统彭艳--中文主页--论文成果

更多

彭艳(教师)

博士生导师硕士生导师
职称 : 教授
学科 :
机械设计及理论
单位 : 机械工程学院

学位 : 博士学位
学历 : 博士研究生毕业
职务 : 教师
出生年月 : 1971-11
入职时间 : 1994-07-01
毕业院校 : 燕山大学

论文成果

[141] 王佳坡.彭艳.Unveiling the local deformation behavior of typical microstructures of nickel-based single crystals under nanoindentation.2022
[142] 彭艳.Dynamic recrystallization behavior of low-carbon steel during hot rolling process: modeling and simulation.2022
[143] 彭艳.邢建康,刘洋.Research on low cycle fatigue life prediction considering average strain.2022
[144] 彭艳.孙建亮.Dynamic recrystallization behavior under steady and transient mutation deformation state.2022
[145] 彭艳.Study on Work Roll Vertical Vibration Under Periodic Spalling of the Oxide Film.2022
[146] 李群.彭艳,石宝东.Effect of axial preloading on mechanical behavior during the free-end torsion of an extruded AZ31 magnesium alloy.2022
[147] 王玉辉.王天生,彭艳.Tailoring the microstructure to enhance the cryogenic mechanical properties of a Fe–34.5Mn–0.04C steel.2022
[148] 孔维航.闫鹏.Multi-Phase Measurement of Oil Production Using Fiber-conductance Dual-Mode Sensor.2022
[149] 李志明.于丙强,彭艳,杨利坡,刘宏民.A New Mehtod of Generating Excited Signal and its Application in the Piezomagnetic Type Shape Meter.IEEE Computer Society.2010
[150] zhang,yongzhen.刘宏民,孙建亮,彭艳.Spray cooling rate model of heavy cylinder rolling.TTP.2014
[151] 邢春玲;彭艳;邢建康;臧勇.彭艳.温轧及球化退火对45钢组织与性能的影响.2015
[152] 刘宏民.孙建亮,陈素文,彭艳.Strip layer method for analysis of the three-dimensional stresses and spread of large cylindrical shell rolling.2015
[153] 张明.孙建亮,彭艳.2160mm热连轧机组F2精轧机振动机理及测试.2016
[154] 彭艳.Effect of Deformation on Microstructure and Mechanical Properties of Medium Carbon Steel During Heat Treatment Process.2021
[155] 彭艳.Characterization of dynamic recrystallization behavior of low carbon steel under flexible rolling process.2021
[156] SCR连铸连轧铜杆表面铜粉形成机理及其质量控制.2021
[157] 陈素文.孙建亮,刘宏民,彭艳.Calculation of Rolling Force of 3700mm Cylindrical Shell Rolling Mill.Trans Tech Publications.2012
[158] 杨冲.彭艳,石宝东.Mechanical Anisotropy Induced by Strain Path Change for AZ31 Mg Alloy Sheet.2020
[159] 杨宝成.彭艳,石宝东.Anisotropic mechanical behavior and corresponding microstructure evolution of extruded AZ31 under combined normal/shear stress states.2019
[160] 彭艳.基于板形板厚控制的轧机系统动态建模及仿真研究进展.2010

共218条 8/11

首页上页下页尾页页

同学科博导

同学科硕导

扫一扫用手机查看